manualshive.com logo in svg

Huawei FusionModule500, User Manual

Share
Download
Huawei FusionModule500 User Manual Download Page 296

Context

The water detector is installed in the cabinet and bound to the rack rail using

cable ties. The binding position is 5 U away from the cabinet bottom.
A water sensor consists of a water detection cable, water detector, and conversion

cable. The water detection cable is laid out on the floor, connecting to the water

detector placed near the collector by the conversion cable.

Figure 6-26 Water sensor components

(1) Water detector

(2) Conversion cable end A,

connected to the water detector

(3) Conversion cable

(4) Conversion cable end B,

connected to the water

detection cable

(5) Water detection cable end A,

connected to the conversion cable

(6) Water detection cable

Procedure

Step 1 Replace the water detector.

1. Remove the conversion cable at the conversion port for the water detector

and conversion cable.

2. Remove the cover from the water detector.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

Copyright © Huawei Technologies Co., Ltd.

286

Summary of Contents for FusionModule500















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands