Huawei FusionModule500 User Manual Download Page 242

Page: 242 / 302

Procedure

Step 1 On the CloudOpera NetEco app, tap

in the upper right corner.

Step 2 On the Create network screen, enter network information as prompted and tap

Confirm.

Figure 5-58 Creating a network

Table 5-27 Parameter description

Parameter

Description

Network Name

Name of the network.

ESN

ESN of the ECC controller.

NOTE

Tap

to scan the QR code on the ECC controller to

obtain the ESN.

Longitude

Longitude of the network. You can manually enter the

value or use GPS to locate.

Latitude

Latitude of the network. You can manually enter the

value or use GPS to locate.

Customer Information Customer information.

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

232

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands