Huawei FusionModule500 User Manual Download Page 85

Page: 85 / 302

Cable

NO TICE

● The site ground resistance must be less than 0.1 ohm.
● The cable fire resistance rating must be at least VB.

Table 4-8 Cable specifications

Application Scenario

Specifications

Remarks

(Optional) Outdoor unit

power cable

Electrical power cable,

600 V, ZA-RVV, 4 x 2.5

, black (four core

wires: brown, black, blue,

yellow/green), 46 A,

outdoor cable, CE

The length is determined

based on site survey.

Common terminal,

single-wire cord end

terminal, 2.5 mm

insertion depth 12 mm,

blue

Delivered with the

fittings

Bare crimp terminal, OT,

2.5 mm

, M4, tin plated,

16–14 AWG

Delivered with the

fittings

4.2.4.2 Layout Principles

The layout principles are as follows:

●

If the outdoor unit is placed higher than the indoor unit, the maximum height

deviation between them should be less than or equal to 20 m. Install an oil

trap every 6 m to 7.5 m along the gas pipe in the vertical direction to ensure

system reliability.

●

If the indoor unit is placed higher than the outdoor unit, the maximum height

deviation between them should be less than or equal to 5 m.

NO TICE

● The height deviation refers to the distance between the stop valve of the

indoor unit and that of the outdoor unit.

●

is a sign of a tilt, and indicates that the scale of the pipe tilting is at

least 1:200. The pipe tilting direction should be consistent with the hypotenuse

of the right triangle.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands