Huawei FusionModule500 User Manual Download Page 121

Page: 121 / 302

Procedure

Step 1

Figure 4-53

shows how to connect the water detection cable to the conversion

cable.

Figure 4-53 Connecting cables

(1) Conversion cable end B, connected to the

water detection cable

(2) Water detection cable end A, connected to

the conversion cable

NO TE

The water detection cable and conversion cable are interconnected through the male and

female connectors.

Step 2 Connect the other end of the conversion cable to the water detector, as shown in

Figure 4-54

Figure 4-54 Connecting the water detector

Step 3 Plan the installation position for the fastener of the water detection cable. Ensure

that the water detection cable placed on the fastener is in good contact with the

floor.

Step 4 Tear off the protection paper from the rear of the fastener, and then securely

attach the fastener to the floor.
●

If the fastener cannot be securely attached to the floor, go to

Step 5

●

If the fastener is securely attached to the floor, go to

Step 6

Step 5 Drill holes in the floor with the same dimensions as the expansion bolts for the

fastener. Use the expansion bolts to secure the fastener to the floor, as shown in

Figure 4-55

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

111

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Huawei FusionModule500, User Manual, Page: 121 / 302

Search results

Summary of Contents for FusionModule500

Reviews: