Huawei FusionModule500 User Manual Download Page 245

Page: 245 / 302

Maintenance

Area

Maintenance

Item

Operation

Expected Result Troubleshootin

UPS

Operating

environment

● Ambient

temperature:

0–40°C

● Humidity:

0%–95% RH

(non-

condensing)

● If the

temperature

or humidity

is abnormal,

check the

smart

cooling

product

status.

● If the input

voltage is

abnormal,

check the

power grid

status and

input cable

connection.

Liquid crystal

display (LCD)

According to the

status icons on

the LCD, all units

are operating

properly. No

fault or alarm

information is

found in the

active and

historical alarm

records.

If an alarm is

present, rectify

the fault by

checking the

device status

and parameters.

Lithium battery

Battery

management

alarm

No battery

management

alarm is

generated.

Identify the

cause of an

alarm based on

the alarm

information.

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

235

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands