Huawei FusionModule500 User Manual Download Page 221

Page: 221 / 302

1. On the home page of the iClient, choose System Management > Device

Management > Device Management > Micro Edge.

2. Right-click an IVS1800 and choose Camera Access.
3. Select Auto Batch Access and click Start.
4. Set the IP address segment.

Figure 5-48 Setting an IP network segment

NO TE

– The driver protocol of IPC6325 and C3220 cameras is HWSDK.
– The IP address segment indicates the start and end IP addresses of cameras.

5. You can use IP Address and Vendor to filter the required cameras in the

camera search result and select the required cameras. Alternatively, you can

directly select the required cameras in the camera list. Then verify accounts.

The default password of the HWSDK protocol is HuaWei123.

Figure 5-49 Verifying accounts

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

211

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands