Huawei FusionModule500 User Manual Download Page 248

Page: 248 / 302

Maintenance

Area

Maintenance

Item

Operation

Expected Result Troubleshootin

Monitor interface

(network

management

system or WebUI)

Export smart

cooling product

logs, alarms,

temperature,

humidity, as well

as the operating

status and time

of the water

sensor, door

status sensor,

temperature

sensor, and

smoke sensor

from the

management

system. View the

historical alarms

generated in this

quarter and

select the most

common five

ones.

If an alarm is

generated,

handle the

alarm by

referring to

and

or contacting

Huawei

technical

support.

Cable connection

The cable

connection is

secure.

Secure loose

cables.

Cables are not

damaged.

Replace

damaged

cables.

Camera

availability

On the ECC800-

Pro WebUI,

choose

Maintenance >

Manage Video >

Video Info to

enter the video

view page. Type

the camera name

or IP address to

find the camera,

and click View to

view the real-

time monitoring

page.

The monitoring

page is properly

displayed after

you click View.

If the

monitoring

page is not

displayed after

you click View,

check that the

IP address is

correctly set,

and check cable

connections or

replace the

camera. For

details, see

6.4.3.5

Replacing a

Camera

FusionModule500 Smart Mini Data Center

User Manual

6 O&M

Issue 02 (2020-12-25)

238

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands