Huawei FusionModule500 User Manual Download

Page: 165 / 302

Battery Capacity

Description

● Default value: 100 Ah
● Value range: 50–2400 Ah. The value

increases by 50 Ah each time you

press SELECT.

Step 5 Press and hold ON/MUTE for more than 5s. Release the button when you hear a

beep sound. The UPS starts to work in battery mode.

Figure 5-2 Battery mode

Step 6 After you ensure that the UPS runs properly, switch on the AC output circuit

breaker Q for the UPS to start the load.

----End

5.1.2 Connecting the Lithium Battery Supply

Procedure

Step 1 Switch on the lithium battery circuit breakers.

Step 2 Check whether the lithium batteries communicate properly. If the running

indicator on a lithium battery is steady on, the lithium battery communicates

properly with the SMU. If the indicator blinks fast (4 Hz), the communication is

interrupted. In this case, check that the communications cable is properly

connected.

Step 3 Observe the lithium batteries for 15 minutes. The batteries are running properly if

the alarm indicators are off.

Step 4 Hold down the MANUAL ON/OFF buttons on the lithium battery panels for more

than 5s and less than 15s to activate the lithium batteries.

----End

5.2 Power-On Commissioning for the Cooling System

FusionModule500 Smart Mini Data Center

User Manual

5 Power-On Commissioning

Issue 02 (2020-12-25)

155

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands