manualshive.com logo in svg

Huawei FusionModule500, User Manual, Page: 112 / 302

Share
Download
Huawei FusionModule500 User Manual Download Page 112

Procedure

Step 1 Install busbars.

1. Open the cabinet rear door.
2. Install floating nuts at the busbar installation position.
3. Secure the busbar to the installation position using screws.

NO TE

The busbar is installed 2 U above the last lithium battery. Determine the busbar

installation position based on the lithium battery configuration.

Figure 4-42 Installing busbars

----End

4.2.5.3 Installing PDU2000s

Context

Two half-height rPDUs for vertical installation are configured.

Procedure

Step 1 Install a half-height PDU2000.

1. Open the cabinet rear door.
2. Secure the half-height PDU2000 to the installation position using screws.

Step 2 Install the other PDU2000 in the same way.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

Copyright © Huawei Technologies Co., Ltd.

102

Summary of Contents for FusionModule500















































































































































































































































































































Reviews:

No comments