Huawei FusionModule500 User Manual Download Page 66

Page: 66 / 302

●

Connect equipotential cables to metal components without carrying currents

in the module, such as metal doors and windows. Each equipotential cable

has a minimum cross-sectional area of 6 mm

3.6 Cable Management

A cable tray is used inside a cabinet to route cables from the front to the rear.

Cable Tray

A cable tray is used for forward and backward cabling. It uses mounting ears to

facilitate device installation.

Figure 3-23 Cable tray

Table 3-42 Cable tray technical specifications

Dimensions (H x W x

Weight

Space Occupied

43.6 mm x 482.6 mm x

250 mm

1.89 kg

1 U

FusionModule500 Smart Mini Data Center

User Manual

3 System Architecture

Issue 02 (2020-12-25)

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands