Huawei FusionModule500 User Manual Download Page 151

Page: 151 / 302

Figure 4-108 Cable route example in the bottom cable routing scenario

4.3.3.3 Connecting PDU2000 Power Cables

Context

If the PDU2000 is not configured with industrial connectors, connect the PDU2000

cables.

Preparations

Tools: Phillips screwdriver, flat-head screwdriver, diagonal pliers, protective gloves
Material: cable tie

Procedure

Step 1 Connect the PDU2000 cables.

NO TICE

● If PDU2000 cables have been connected onsite, go to

Step 2

● Connect cables to the PDU2000 based on the type of the PDU2000 and the silk

screen on the wiring port. The following cable connection is for reference only.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

141

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Related manuals for FusionModule500

Brands by name

Popular brands