Huawei FusionModule500 User Manual Download Page 132

Page: 132 / 302

Figure 4-73 Removing the upper cover of the chassis

NO TE

When removing the upper cover from the chassis, do not use one hand to perform this

operation. Otherwise, the upper cover may collide with the components inside the device,

bringing risks of component damages.

4. Take two #6-32UNC screws from the screw package (there are eight screws in

the package) and preinstall the two screws in the holes near the cable outlet

on the hard disk backplane. Tighten the screw threads for three circles (ensure

that the screws do not fall naturally).

Figure 4-74 Installing disk screws

5. Insert the SATA and power cables into the corresponding ports on the hard

disk. During cable connection, ensure that the metallic plate of the SATA

cable faces upward.

FusionModule500 Smart Mini Data Center

User Manual

4 Installation Guide

Issue 02 (2020-12-25)

122

Summary of Contents for FusionModule500















































































































































































































































































































Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands

Huawei FusionModule500, User Manual

Search results

Summary of Contents for FusionModule500

Reviews:

Brands by name

Popular brands