Huawei FusionModule 1000A40 Maintenance Manual Download | Manualshive

Page: 186 / 199

background image

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

6 Emergency Operations

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

178



If the ATS switchover fails, manually switch the ATS to the other mains or DG supply,
and check whether all devices are working properly.

Step 3

Monitor the system running until the mains supply is stored and the system is working
properly.

----End

Follow-up Procedure

Analyze the cause of the fault, and work out and record the preventive measures.

6.2 Emergency Operations for Circuit Breaker Tripping

Prerequisites

A circuit breaker has tripped.

Important devices of the FusionModule1000 are powered by two power supplies. If one circuit breaker
trips, it does not affect the operation of importance devices. However, the situation needs to be handled
promptly to avoid jeopardizing the long term stable running of the equipment.

Procedure

Step 1

Promptly locate the control range of the circuit breaker that has tripped.

Step 2

Analyze the cause of the circuit tripping and switch on the circuit breaker as soon as possible.

----End

Follow-up Procedure

Analyze the cause of the fault, and work out and record the preventive measures.

6.3 Emergency Operations for Overload

Prerequisites

An overload alarm is generated.

Procedure

Step 1

Locate the cable or device based on the alarm information.

Step 2

Check the overloaded cable or device and locate the fault.

If the cable or device is seriously overloaded, immediately power off the device and its lower-level
devices.

----End

«
...
184
185
186
187
188
...
»

Summary of Contents for FusionModule 1000A40








































































































































































































Reviews:

No comments

Related manuals for FusionModule 1000A40

Brand: GALLERY Pages: 18

Brand: CAMAG Pages: 40

Brand: dbx Pages: 2

Brand: Eagle Group Pages: 8

Brand: ProLights Pages: 28

Brand: ASIA TECHNOLOGY Pages: 38

Brand: Qdot Pages: 6

Brand: 2connect Pages: 8

Brand: Hailo Pages: 20

Brand: CARDIOSTRONG Pages: 52

Brand: Vascular Pages: 64

Brand: Yellowtec Pages: 27

Brand: WALU Pages: 4

B-Control Deejay BCD3000

Brand: Behringer Pages: 13

Brand: CAMP Pages: 148

Brand: HQ Power Pages: 63

Brand: K&S Pages: 6

Tone Works Pandora PX4D

Brand: Korg Pages: 196

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands