Huawei FusionModule 1000A40 Maintenance Manual Download Page 22

Page: 22 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

3 Maintenance

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Device

Operation

Check
Standard

Troubleshooting

Fire
extinguishe
r

Check the
appearance of the
fire cylinder,
electromagnetic
valve, pipeline, and
nozzle.

All devices of
the fire
extinguisher
are intact, free
from
deformation
and
mechanical
damage.

Replace the fire cylinder. For details
about how to replace other devices,
contact Huawei technical support.

All devices of
the fire
extinguisher
are free from
rust on the
exterior, and
the coating is
intact.

Repaint.

The lead seal
and safety
signs on
hand-operated
devices are
intact.

Replace the electromagnetic valve.

Read the pressure
shown on the
pressure gauge.

The pressure
pointer is in
the green zone.

Ask a local maintenance engineer to
check whether the fire cylinder
leaks extinguishant. If leakage
occurs, the maintenance engineer
asks the fire extinguisher
manufacturer to recharge the
extinguishant.

Emergency
light

Press

TEST

on the

emergency light
panel.

The
emergency
light turns on
when you
press

TEST

Check whether the voltage of the
input power supply is normal,
and rectify any cable connection
fault identified.

Replace the emergency light If
the input power supply is
normal.

Check the power
indicator.

The power
indicator is
steady green,
and the fault
indicator is off.

Replace the emergency light.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands