Huawei FusionModule 1000A40 Maintenance Manual Download Page 135

Page: 135 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

127

Figure 5-55

Removing the safety pin

Reinstall and tighten all screws.

----End

Follow-up Procedure

Dispose of the removed fire cylinder that is confirmed faulty.

5.4.9 Charging Extinguishant

Prerequisites



The fire cylinder has passed the air-tightness test.



Tools and materials are ready.



All tools and materials except the camshaft device are provided by the charging station.



Extinguishant needs to be charged in the charging station.

Preparations

Tools: platform scale, hose with a pressure tolerance greater than 2.5 MPa, gate valve,
camshaft device, pipe wrench, adjustable wrench

Materials: extinguishant charging cylinder with sufficient extinguishant, nitrogen cylinder
with sufficient nitrogen

Documents: fire extinguishing device installation position diagram (standard)

Skill requirement: fire engineer

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands