Huawei FusionModule 1000A40 Maintenance Manual Download Page 174

Page: 174 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

166

Figure 5-90

Removing the extinguishant abort button

Step 3

Disconnect the cables from the extinguishant abort button, and remove the panel of the
extinguishant abort button.

Figure 5-91

Disconnecting cables from the extinguishant abort button

As a resistor is installed on the loop of the extinguishant abort button, remove the resistor, and connect
the resistor to the corresponding terminals of the new extinguishant abort button when you replace the
extinguishant abort button.

Step 4

Remove the screws on the extinguishant abort button base using a Phillips screwdriver, and
remove the base.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands