Huawei FusionModule 1000A40 Maintenance Manual Download

Page: 19 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

3 Maintenance

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Item

Method

Expected
Result

Troubleshooting

air-cooled
precision
air
conditioner
s

The air filters
are not
damaged or
misshapen.

If an air filter is damaged or
misshapen, replace air filters for a
20 kW air-cooled precision air
conditioner.

Screws
securing the
compressor
of the 20
kW
air-cooled
precision
air
conditioner

Check screws
securing the
compressor.

The
compressor
screws are
secure.

If a compressor fan screw is loose,
tighten the screw.

Service
valves of
the 20 kW
air-cooled
precision
air
conditioner
s

Check the
compressor service
valves.

The
compressor
service valves
have no oil
stains.

If a compressor service valve is
covered by oil stains, clean the oil
stains.

Compressor
running
sound of
the 20 kW
air-cooled
precision
air
conditioner

Listen to the
compressor
running sound.

No abnormal
noise is
generated.

If the compressor generates
abnormal noise, replace the
compressor by following
instructions in

NetCol5000-A 20 kW

Air-Cooled In-Row Precision Air
Conditioner User Manual

Evaporators
of the 20
kW
air-cooled
precision
air
conditioner
s

Check the
evaporators.

No foreign
matter exists
on the
evaporator
surfaces.

If an evaporator is covered by
foreign matter, clean the foreign
matter.

Refrigerant
pipes of the
20 kW
air-cooled
precision
air
conditioner
s

Check the
refrigerant pipes.

The refrigerant
pipes do not
leak, are not
corroded, and
are properly
wrapped with
thermal
insulation
foam.

In the case of pipe leakage, pipe
corrosion, or thermal insulation
foam damage, repair the leakage
and corrosion, and rewrap the
thermal insulation foam.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands