Huawei FusionModule 1000A40 Maintenance Manual Download Page 190 | Manualshive

Page: 190 / 199

background image

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

6 Emergency Operations

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

182

6.8 Emergency Operations for a Single Fire Alarm
(Standard)

Prerequisites

The management system reports a single fire alarm.



The following single fire alarm emergency operations are for reference only.



If a single fire alarm is generated, determine whether to extinguish the fire or leave the
area immediately based on the actual situation and contact the personnel on duty or fire
engineer.

Procedure

Step 1

Locate the alarm or alarm area in the management system.

Step 2

Check the internal situation in the video surveillance system.



If the video surveillance system indicates that everything is normal, go to



If onsite fire is confirmed, go to

Step 3

Check whether extinguishant has been released.



If extinguishant is being released, contact the local maintenance engineer or Huawei
technical support to recharge the extinguishant after the fire has been extinguished.



If no extinguishant is released, check the situation onsite, and contact the fire engineer.

Step 4

Arrive at the site with necessary tools and communications devices as soon as possible, open
the external fire control box, and press the

EMERGENT RELEASE

on the fire alarm

control panel.

«
...
188
189
190
191
192
...
»

Summary of Contents for FusionModule 1000A40








































































































































































































Reviews:

No comments

Related manuals for FusionModule 1000A40

Brand: Oberheim Pages: 40

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: Danelec Pages: 67

Brand: Garelick Pages: 4

Brand: P-Q Controls Pages: 5

Brand: P+L Systems Pages: 2

Brand: Yamaha Pages: 5

Brand: Cannon Pages: 70

Brand: Sakai Pages: 31

Brand: Össur Pages: 16

Exoform Dorsal Night Splint

Brand: Össur Pages: 34

Brand: MAKSIWA Pages: 155

Brand: Dräger Medical Pages: 204

SnapTable PRO Hyper-Lite

Brand: SWENSON SHEAR Pages: 12

Brand: Ambu Pages: 32

Brand: Reichert Pages: 28

Brand: Qdot Pages: 6

Unidrill-W Series

Brand: Moore Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands