Huawei FusionModule 1000A40 Maintenance Manual Download Page 82

Page: 82 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential



There is a PC light shade for the light of a pre-fab. module of the standard version.
Remove the PC light shade when replacing the light.

Impact on the System

The lighting system is interrupted temporarily.

To facilitate light replacement, prepare a portable light.

Preparations

Tools: insulation gloves, step ladder (2 m), portable light

Material: spare light tube

Document: lighting device layout diagram

Skill requirement: none

For the diagram, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Disconnect the power switch of the light.

Step 2

(Optional) Push up the PC plate with both hands. When the PC plate is higher than the
limiting structure, slide the PC plate towards the middle of the ceiling until the PC plate
contacts the L-shaped stop plate in the middle of the ceiling.

Figure 5-6

Moving a PC plate

(1) PC plate

(2) L-shaped stop plate

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands