Huawei FusionModule 1000A40 Maintenance Manual Download Page 31

Page: 31 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

3 Maintenance

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Maintenance Item Operation

Check Standard

Troubleshooting

Humidifier water
refill of the 20 kW
air-cooled precision
air conditioner

Flip the manual
drainage button of
the humidifier to O:
normal
humidification.

If water can be
normally refilled
into the humidifier,
the water refill pipe
is unobstructed.

If the water refill is
abnormal:



If the water inlet
solenoid valve
cannot be
opened, perform
replacement by
following
instructions in
documents
delivered with
the air
conditioner.



If the water refill
pipe is blocked,
clean the pipe.



If the humidifier
cylinder is dirty
and the water
level inside the
cylinder is above
4/5, replace the
humidifier
cylinder by
following
instructions in

NetCol5000-A 20
kW Air-Cooled
In-Row Precision
Air Conditioner
User Manual

Thermal insulation
foam of the water
refill pipe,
drainpipe, and vapor
hose of the
humidifier

Check the thermal
insulation foam of
the water refill pipe,
drainpipe, and vapor
hose.

The thermal
insulation foam is
intact.

Replace the thermal
insulation foam if
the thermal
insulation foam is
damaged.

Interior of the
humidifier cylinder

Check the interior of
the humidifier
cylinder.

The interior is free
from scale.



If there is scale
on the interior of
the humidifier
cylinder, remove
the humidifier
cylinder and
clean it with 20%
acetic acid

Phase currents when
the humidifier is
working

Measure the phase
currents when the
humidifier is
working.

Each phase current
is no less than 1.2 A
(1/3 of the rated
current).

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands