Huawei FusionModule 1000A40 Maintenance Manual Download

Page: 103 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential



A spare RH2288 server of the same model is available and functional.

Impact on the System

The operation of the RH2288 system or devices may be interrupted.

Preparations

Tools: Phillips screwdriver, small-sized flat-head screwdriver, ESD gloves, marker

Materials: spare RH2288 server

Documents: documents delivered with the RH2288 server, management system initial
configuration table, monitoring device layout diagram

Skill requirement: weak-current engineer

For the diagrams and tables, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Press and hold the power switch on the front panel of the RH2288 server for about 5s to
power off the server, and disconnect the power plug.

Step 2

Mark cables and ports on the RH2288 server using a marker.

Step 3

Remove all cables connected to the RH2288 server.

Step 4

Remove the faulty RH2288 server using a Phillips screwdriver and install a new RH2288
server.

Figure 5-21

Installing the RH2288 server

Step 5

Reconnect the cables and the power plug.

Step 6

Press and hold the power switch on the front panel of the RH2288 server for about 5s to
power on the server, and check that the RH2288 server is working properly.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands