Huawei FusionModule 1000A40 Maintenance Manual Download Page 183

Page: 183 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

175

Preparations

Tools: Phillips screwdriver, flat-head screwdriver, step ladder, protective gloves

Materials: spare emergency light

Documents: none

Skill requirement: fire engineer

For the diagrams, see the initial configuration parameter manual for the solution in use.

Procedure

Step 1

Disconnect the power plug of the emergency light.

Figure 5-98

Removing the power plug

Step 2

Remove the protective cover of the emergency light.

Step 3

Loosen the emergency panel using a flat-head screwdriver, and remove the panel.

Step 4

Remove screws from the emergency light base using a Phillips screwdriver, and remove the
base.

Step 5

Install the new emergency light base and the panel in the same way.

Step 6

Remove the red pin, and reinstall the protective cover.

Figure 5-99

Position of the red pin

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands