Huawei FusionModule 1000A40 Maintenance Manual Download

Page: 180 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

172

Connect the I-shaped connection pipe to the threaded adapter.

Connect the high-pressure hose.

Step 11

Reinstall the electrical actuator to the container valve of the fire cylinder.

Verify that the electrical actuator ejector is reset. If the ejector is not reset, press down
the ejector.



That the ejector is not reset may lead to extinguishant release.



The electrical actuator ejector is 11 mm long before being pressed down, and 7 mm long
after being pressed down.

Figure 5-96

Operating the electrical actuator ejector

Align the electrical actuator and the container valve, and tighten the actuator clockwise.

Step 12

Switch on the input circuit breaker of the extinguishant control panel and connect the battery
cables to power on the panel.

----End

Follow-up Procedure

Dispose of the removed fire cylinder that is confirmed faulty.

5.6.10 Replacing the Extinguishant Control Panel (CE)

Prerequisites

A spare extinguishant control panel of the same model is available and functional.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands