Huawei FusionModule 1000A40 Maintenance Manual Download Page 25

Page: 25 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

3 Maintenance

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Device

Operation

Check Standard

Maintenance Guide

fire extinguishing
pipeline, and
nozzle.

All devices of the
fire extinguisher are
free from rust on the
exterior, and the
coating is intact.

Repaint.

The lead seal and
safety signs on
hand-operated
devices of the fire
cylinder are intact.

Replace the electrical
actuator.

Check the pressure
pointer of the fire
cylinder.

The pressure pointer
is in the green zone.

Ask a fire engineer to check
whether the fire cylinder leaks
extinguishant. If leakage
occurs, the fire engineer
charges the extinguishant in
the local charging station.

Emergency
light

Disconnect the
power plug of the
emergency light.

The emergency light
turns on.

Replace the emergency light.

Smoke
detector

Check the smoke
detector indicator.

The indicator blinks
once every 6s.

Replace the smoke detector.

Heat
detector

Check the heat
detector indicator.

The indicator blinks
once every 6s.

Replace the heat detector.

3.2.7 Other Systems

Table 3-8

Monthly maintenance checklist for other systems

Maintena
nce Item

Operation

Standards
Compliance

Troubleshooting

Pre-fab.
module
paint

Check the
appearance of the
pre-fab. module.

The pre-fab.
module and
bases are free
from paint
flake-off, rust,
or corrosion.

If any part of the pre-fab. module is
damaged or corroded, maintain or
replace the damaged and corroded
part.

Pre-fab.
module
external
environmen
t

Check the pre-fab.
module external
environment.

No hazard or
potential
hazard exists
around the
pre-fab.
module.

If there is potential hazard or
pollutant around the pre-fab.
module, take workaround measures.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Brands by name

Popular brands