Huawei FusionModule 1000A40 Maintenance Manual Download Page 115

Page: 115 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

107

Figure 5-32

Removing a smoke sensor

Step 3

Remove cables from the base using a Phillips screwdriver.

As a terminal resistor is connected to the last smoke detector in the loop in parallel, remove the terminal
resistor from the faulty smoke detector, and connect the resistor to the new smoke detector when you
replace the smoke detector.

Step 4

Remove the screws on the base using a Phillips screwdriver, and remove the base.

Step 5

Install the new base to the same position, and reconnect the cables.

Step 6

Hold the new smoke detector body, align the smoke detector indicator with the position
shown by (1) in

Figure 5-33

, and turn the detector body clockwise to the position shown by (2)

Figure 5-33

to install the smoke detector.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands