Huawei FusionModule 1000A40 Maintenance Manual Download Page 99

Page: 99 / 199

FusionModule1000A40 IT Solution
Maintenance Guide (2016.05, AI Version)

5 Components Replacement

Issue 04 (2018-01-05)

Huawei Proprietary and Confidential

Step 5

Install a new VCN500.

Push the VCN500 into the cabinet along the guide rails and gently press down the
buttons on the upper and lower mounting ears.

Figure 5-17

Placing a VCN500

Tighten the captive screws in the ears using a Phillips screwdriver to close the mounting
ear buttons.

Figure 5-18

Installing a VCN500

Step 6

Reconnect the cables and the power plug of the VCN500.

Step 7

Check whether the new VCN500 is working properly.



If the VCN500 power indicator is steady green, the VCN500 is working properly.



If the network port ACT indicator blinks green, data transmission is normal.



If the hard disk active indicator blinks green, the hard disk reads data properly.

Summary of Contents for FusionModule 1000A40








































































































































































































Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands

Huawei FusionModule 1000A40, Maintenance Manual

Search results

Summary of Contents for FusionModule 1000A40

Reviews:

Related manuals for FusionModule 1000A40

Brands by name

Popular brands