manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 67 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 67

Parameter

Description

Output mode

This specifies the format of the video received by the display. If
the interface is an SDI OUT interface, this parameter does not need
to be set. Otherwise, the setting of this parameter is mandatory.

l

VGA

: Select this option if connecting the display to an HD

OUT interface using a DVI-SXGA conversion cable.

l

DVI

: Select this option if connecting the display to an HD OUT

interface using a DVI extension cable.

l

YPrPb

: Select this option if connecting the display to an HD

OUT interface using a DVI-YPrPb conversion cable.

l

DVI (AUDIO)

: Select this option if connecting the display to

an HD OUT interface using a DVI-HDMI conversion cable.

Stretch mode

This specifies whether to adjust a video to fit the video into the
screen.

l

Stretch

: The aspect ratio can be changed.

l

No stretch

: The aspect ratio remains unchanged.

l

Intelligent stretch

: The system cuts the video to a proper size,

and then stretches the video to the full-screen mode after
locking the aspect ratio. For example, to change a wide-screen
video to a narrow-screen video, the system cuts the left and right
sections of the wide-screen video, and then stretches the video
to the full-screen mode.

Video resolution

For details about how to set the video resolution, see 

Table 3-17

.

Refresh rate

For details about how to set the refresh rate, see 

Table 3-18

.

Display local video
Display remote video
Display H.239

This specifies the content displayed on the interface. You can
choose between local video, remote video, local presentation, and
remote presentation.
For details about the content that can be displayed on each video
output interface, see 

Table 3-12

, 

Table 3-13

, 

Table 3-14

, and

Table 3-15

.

By default, the local video, remote video, and presentation can be
displayed on the monitor connected to the HD OUT 1 interface.
Only the video output from the HD OUT 1 interface can be
manually switched. For details about the switching method, see
section 

7.6 Adjusting the Screen Layout

.

After specifying the display content for the HD OUT 2 interface
or the HD OUT 3 interface, you cannot change the content during
a conference. For example, if 

Display local video

 is selected for

the HD OUT 2 interface, only the local video can be displayed on
the monitor connected to the HD OUT 2 interface during
conferences. If 

Display H.239

 is selected for the HD OUT 2

interface, the monitor connected to the HD OUT 2 interface can
display only the local presentation before a conference and only
the remote presentation during a conference.

HUAWEI 9000 HD Video Terminal
Administrator Guide

3 Camera and Display

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

55

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments