manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 71 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 71

Video Resolution

Refresh Rate (Hz)

1080p

24, 25, 30, 50, and 60

 

A higher refresh rate contributes to smoother video quality. The refresh rate selected should
match the refresh rate of the display.

Configuring SD Video Output Interfaces

Select an SD video output interface to be configured, such as the SD OUT 1 interface, and then
set the parameters listed in 

Table 3-19

.

The quality of the video output from the S-Video video output interface is better than that output
from the CVBS video output interface. Therefore, it is recommended that you use the S-Video
video output interface on priority. The S-Video and CVBS video output interfaces of the terminal
need to be connected to different displays. Otherwise, the video cannot be displayed properly.

Table 3-19

 SD video output parameters

Parameter

Description

Name

This specifies the name of an output interface to simplify identifying and
using the interface during a conference.

Video
resolution

You can select either 

PAL

 or 

NTSC

 for any output mode.

Output mode

This specifies the format of the video received by the display.

l

CVBS

: Select this option if the display provides an interface for this

format. If the video is output from the SD OUT 2 interface on the
terminal, use an S-Video-CVBS conversion cable.

l

S-Video

: Select this option if the display provides an interface in this

format. If the video is output from the SD OUT 1 interface on the
terminal, use a CVBS-S-Video conversion cable.

Stretch mode

This specifies whether to adjust the aspect ratio of a video to fit the video
into the screen.

l

Stretch

: The aspect ratio can be changed.

l

No stretch

: The aspect ratio remains unchanged.

l

Intelligent stretch

: The system cuts the video to a proper size, and then

stretches the video to the full-screen mode after locking the aspect ratio.
For example, to change a wide-screen video to a narrow-screen video,
the system cuts the left and right sections of the wide-screen video, and
then stretches the video to the full-screen mode.

 

To ensure the quality of the video output from the terminal, the resolutions of the videos input
to and output from the terminal need to match each other. For example, if a video with a resolution
of 1080p and a frame rate of 30 is input to the terminal, set the resolution of the output video to
1080p and the frame rate to 30 Hz or 60 Hz. If a video with a resolution of 1080p and a frame

HUAWEI 9000 HD Video Terminal
Administrator Guide

3 Camera and Display

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

59

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments