Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 109

Page: 109 / 204

Parameter

Description

Number

This specifies the site number used to make calls between sites.

IP, SIP, E1/T1/4E1, and H.323 Phone site numbers are allocated
by the videoconferencing service provider.

PSTN site numbers are telephone numbers.

Type

This specifies the line used by the terminal to access the
videoconferencing network.

Type

is set to

, the terminal uses the protocol set for

Preferred IP protocol

For Cisco TelePresence sites, you must select

SIP

as the line

type.

Rate

This specifies the rate supported by the terminal over the
corresponding access line used by the site.
It is recommended that you select the highest rate.

Line port

This specifies the line used by the terminal to communicate with the
site. This parameter is valid for E1 sites.

Country/Region code

This specifies the country or area where the site is located.

Area code

This specifies the area code of a local ISDN site's conference line.
Set this parameter based on the country/region configured for the
site.

IP address

This specifies the IP address of the site.

URI

This specifies the site's Uniform Resource Identifier (URI). For
example, [email protected].

NOTE

This parameter is available only when

Type

is set to IP, H.323, or SIP.

Step 3

Select

Save

----End

Creating a Group

If certain sites join a conference regularly, they can be defined as a group.

Procedure

Step 1

On the

Address Book

screen, select

Create Group

to display the

Create Group

screen.

Step 2

Enter a name for the group in the text box. The name cannot consist of only digits.

Step 3

Select the sites to be added to the group from the address book. Each selected site is marked
with a tick (

√

) before the site name and all the sites that are added to the group appear in the site

list.

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Summary of Contents for 9000 VCT V100R011













































































































































































































Search results

Summary of Contents for 9000 VCT V100R011

Reviews:

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 109 / 204

Search results

Summary of Contents for 9000 VCT V100R011

Reviews: