manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 122 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 122

Procedure

Step 1

From the home screen, select 

Settings

, enter the administrator password (if set), and then select

OK

 to display the 

Settings

 screen.

Step 2

Select 

Conference

 > 

Select conference control operation

, and then select the conference

control options as required.

Step 3

Select 

Save

 to save the settings.

----End

6.3 Viewing Sites

You can view a single site or view multiple sites in turn.

On the 

View Site

 screen, you can view a single site or view multiple sites in turn at preset

intervals.

NOTE

During multipoint conferences hosted by standalone MCUs, the terminal supports multiple continuous
presence views.

This function is different for the chair site and a non-chair site.

Non-Chair Site

The function of viewing sites is available when no site is being broadcast and no continuous
presence is displayed during a conference.

A non-chair site can view the video of another site that is under the same-level MCU and cannot
view the video of another site that is under a different-level MCU.

Chair Site

The chair site can view any of the sites participating in the conference.

The function of viewing sites is still available when a site is being broadcast or the continuous
presence is displayed during a conference.

6.4 Broadcasting Sites

All the sites (except for the broadcasting site) are forced to view the broadcasting site.

The chair site can broadcast any of the sites participating in a conference (except for an audio-
only site) or broadcast multiple sites (including the chair site) in turn at preset intervals.

When a site is being broadcast, all non-chair sites are forced to view the broadcasting site while
the chair site can view any of the sites participating in the conference.

To stop broadcasting a site, select 

Stop

 or 

Discussion

.

After the chair site stops broadcasting a site, all the sites in the conference can view any other
site. 

Stop

 is available when there is a broadcasting site in the conference.

HUAWEI 9000 HD Video Terminal
Administrator Guide

6 Conference Control

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

110

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments