Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 135

Page: 135 / 204

Parameter

Description

Locally output
sound from
AUDIO IN

If this function is enabled, you can hear the input from the AUDIO IN
interface at the local site.

Step 2

Save the settings.

----End

7.3 Adjusting the Volume at the Local Site

You can adjust the output volume of the local speaker by pressing

on the remote

control.

Press

to increase the volume or

to decrease the volume. The adjustment affects the

volume heard only at the local site.

7.4 Enjoying Stereo Audio

In dual-audio-channel mode, stereo effect audio can be enjoyed allowing users to accurately
locate the direction from which the sound comes, thus gaining a true-to-life experience. The
input sources for the left and right audio channels can be set.

Context

For details about the VPM210, see "

Cascading VPM210s

Procedure

Step 1

Connect the terminal to a microphone and a stereo acoustic system.

Step 2

Choose

Settings

Audio

Audio Input

to specify audio sources for the left and right audio

channels in stereo mode.

When the LAN-POE MIC interface is connected to a VPM210, you do not need to set the stereo
parameter as the VPM210 works in dual-audio-channel mode.

Step 3

Select

Save

to return to the

Settings

screen.

Step 4

On the

Settings

screen, select

Conference

, set

Audio protocol

AAC_LD

HWA-LD

, and

then select

Enable dual audio channel

----End

Follow-up Procedure

During the conference, do not move the microphone unnecessarily. Otherwise, the quality of
stereo audio heard by the remote site is impaired.

HUAWEI 9000 HD Video Terminal
Administrator Guide

7 Video and Audio

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

123

Summary of Contents for 9000 VCT V100R011













































































































































































































Search results

Summary of Contents for 9000 VCT V100R011

Reviews:

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 135 / 204

Search results

Summary of Contents for 9000 VCT V100R011

Reviews: