Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 128

Page: 128 / 204

You can use the preceding conference control functions on the terminal whose built-in MCU is
being used only after selecting

Disable Chair Control

6.25 Locking a Conference

After a conference is locked, a site that is not in the conference cannot join the conference.

If the built-in MCU of a terminal is used during a conference, using the

Lock conference

operation on the terminal whose built-in MCU is being used will prevent additional unwanted
sites from joining the conference.

NOTE

A conference held using cascaded built-in MCUs does not support conference locking.

6.26 Restoring Automatic Continuous Presence

After

Restore Auto Continuous Presence

is selected, the terminal automatically generates

continuous presence. The layout is determined by the continuous presence and adaptation
capabilities of the built-in MCU and the number of sites in the conference.

Automatic continuous presence has four modes: 4 panes, 6 panes, 8 panes, and 9 panes, as listed
in

Table 5-4

HUAWEI 9000 HD Video Terminal
Administrator Guide

6 Conference Control

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

116

Summary of Contents for 9000 VCT V100R011













































































































































































































Search results

Summary of Contents for 9000 VCT V100R011

Reviews:

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 128 / 204

Search results

Summary of Contents for 9000 VCT V100R011

Reviews: