manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 17 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 17

Table 1-3

 Positioning method of each model

Model

Positioning Method

ViewPoint 9039, ViewPoint 9036, and
ViewPoint 9033

The terminal can be placed vertically,
horizontally, or in a cabinet. It is
recommended that the terminal be placed
vertically.

ViewPoint 9035, ViewPoint 9030,
ViewPoint 9039S, HUAWEI VP9035A,
HUAWEI VP9039A, and HUAWEI
VP9036S

The terminal can be placed horizontally or in
a cabinet. It is recommended that the terminal
be placed horizontally.

 

The following sections take the ViewPoint 9039, ViewPoint 9035, and ViewPoint 9030 as
examples and describe their positioning methods.

WARNING

In compliance with the requirements of heat dissipation, do not place any equipment that
consumes large amounts of power within a radius of 500 mm of the terminal. In addition, do not
place any equipment that affects the heat dissipation of the terminal within a radius of 200 mm.
If you place the terminal in a cabinet, ensure that you leave at least 2 U (2 U = 88.9 mm) of space
above the terminal for heat to dissipate.

Placing the Terminal Horizontally

Figure 1-1

 shows the horizontal placement of the ViewPoint 9039 or the ViewPoint 9035. There

are four screw holes in the panel of the terminal. Fasten four screws to install the feet. Place the
terminal horizontally on a table. Ensure that the surface of the panel with the feet faces
downward.

Figure 1-1

 Horizontal placement 1

 

Figure 1-2

 shows the horizontal placement of the ViewPoint 9030.

Figure 1-2

 Horizontal placement 2

HUAWEI 9000 HD Video Terminal
Administrator Guide

1 Installation and Preparation

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

5

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments