manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 181 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 181

Problem

Possible Cause

Solution

After startup, the
terminal cannot be
registered with the
gatekeeper.

The settings used for
registration with the
gatekeeper are incorrect. In
other words, 

GK address

, 

H.

323 ID

, or 

Password

 is set

incorrectly.

Choose 

Settings

 > 

Network

 > 

IP

 >

H.323

, and then set the parameters

used for the registration with the
gatekeeper correctly.

Contact the administrator of the
videoconferencing system.
Check whether a site using the
same user name as that of the
local site has already been
registered with the gatekeeper.

Change the user name of the local
site.

Access the 

Line Status

 screen

to check whether the IP
network is disconnected.

Check the IP network settings and
the connection of the IP network
cable. Ensure that the settings are
correct and the cable is connected
properly.

The NAT settings are incorrect.
If the local site is in a private
network and if the gatekeeper
is in a public network, check
whether the local site can
communicate with the
gatekeeper properly. If not, the
local NAT settings are
incorrect.

Choose 

Settings

 > 

Network

 > 

IP

 >

Firewall

, and then set the NAT

parameters properly.

The listen port of the
gatekeeper (such as port 1719)
is restricted by the network
firewall.

Contact the administrator of the
videoconferencing system.

After defining a
conference on the
terminal, a
conference cannot be
initiated.

The terminal is not connected
to the videoconferencing
network.

Check the network and then rectify
relevant faults.

If the local site pays for the
conference, check whether the
account balance of the local site
is sufficient. If another site pays
for the conference, check
whether the corresponding
account number and password
are set correctly and whether
the account balance of the site
is sufficient.

Enter the account number and the
password correctly and top up the
relevant account if necessary.

HUAWEI 9000 HD Video Terminal
Administrator Guide

11 Maintenance and Troubleshooting

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

169

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments