manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 3 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 3

About This Document

Overview

This administrator guide is intended for administrators who configure, customize, manage, and
troubleshoot the Huawei HD video terminal (terminal for short) and the Huawei video terminal
touch panel (touch panel for short).This document is applicable to the following products:
ViewPoint 9030S, ViewPoint 9039 (ViewPoint 9039-T and ViewPoint 9039-M), ViewPoint
9039S (ViewPoint 9039S-M), ViewPoint 9036 (ViewPoint 9036-M), ViewPoint 9035,
ViewPoint 9033, ViewPoint 9030, HUAWEI VP9039A (HUAWEI VP9039A-T and HUAWEI
VP9039A-TS), HUAWEI VP9036S, and HUAWEI VP9035A. 

T

 or 

TS

 indicates that the

corresponding terminal is to be used in a Huawei telepresence system and 

M

 indicates that the

corresponding terminal provides a built-in Multipoint Control Unit (MCU). You can check the
bottom of a product to view its model.

When using this document, note the following:

l

Certain functions described in this document may be unavailable due to restrictions
imposed by function licenses. To use these functions, contact your device provider.

l

The HUAWEI VP9039A-T and the ViewPoint 9039-T are video terminals used in the
Huawei telepresence system. The appearance and operation method of the HUAWEI
VP9039A-T are the same as those of the HUAWEI VP9039A and the appearance and
operation method of the ViewPoint 9039-T are the same as those of the ViewPoint 9039.
Therefore, this document does not explicitly describe the appearance and operation method
of the HUAWEI VP9039A-T and the ViewPoint 9039-T.

l

Chapter 

10 Remote Management from the Web Interface

 and chapter 

11 Maintenance

and Troubleshooting

 describe the operations on the Web interface. The other chapters in

this document describe operations performed using the remote control.

l

The administrator password may be required to access the 

Settings

, 

Utilities

, and

Diagnostics

 screens. For details about how to set the administrator password, see section

9.2.1 Setting the Administrator Password

.

Related Version

The following table lists the product version related to this document.

Product Name

Version

HD video terminal

VCT V100R011

 

HUAWEI 9000 HD Video Terminal
Administrator Guide

About This Document

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

ii

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments