Home
/
Huawei
/
9000 VCT V100R011
/
Administrator'S Manual

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 151 / 204

Share

Page: 151 / 204

Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 151

10

Remote Management from the Web

Interface

About This Chapter

The terminal supports remote management from the Web interface, allowing users to set
parameters, view settings, and control the terminal on the Web interface.

The major features of operating the terminal from the Web interface are as follows:

l

A user can use a computer to access the IP network to which the terminal belongs.

l

When you access the terminal by logging in to the Web interface on a computer, the Web
pages of the terminal are displayed on the computer screen.

l

A maximum of three users can log in to the terminal from the Web interface simultaneously.
After logging in from the Web interface, the administrator can configure the system,
whereas common users can set only personal settings.

l

Users using the remote control to operate on the terminal have a higher level of rights than
users who log in to the terminal from the Web interface. The former can grant control rights
to or revoke the control rights of the latter.

l

The user can import or export an address book from the Web interface.

l

With regard to inputting information in quantity, such as adding sites to the address book,
using the Web interface is more convenient than using the remote control.

10.1 Allowing Login from the Web Interface

Users can log in to the terminal from the Web interface only after the administrator of the terminal
allows them to do so.

10.2 Configuring a Web Browser

Before accessing the terminal from the Web interface, the browser must be configured.

10.3 Logging In to the Terminal from the Web Interface

Before managing the terminal from the Web interface, you need to log in to the Web interface
of the terminal.

10.4 Functions Provided on the Web Interface

The functions provided by a terminal are reorganized on the Web interface for greater ease of
use.

HUAWEI 9000 HD Video Terminal
Administrator Guide

10 Remote Management from the Web Interface

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

139

«
...
149
150
151
152
153
...
»

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments