Home
/
Huawei
/
9000 VCT V100R011
/
Administrator'S Manual

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 99 / 204

Share

Page: 99 / 204

Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 99

Parameter

Description

Initial conference
mode

If you use the built-in MCU of the HUAWEI VP9039A to initiate a
conference, you can set this parameter to either of the following:

l

Free view

: All the sites participating in the conference can choose

to view a specific site. In addition, each site can set and view
continuous presence as desired. If this option is selected,

Viewing

mode

or

Voice activation

cannot be selected from the

Conference

screen.

l

Broadcast

: After the conference starts, a site in full screen or

multiple sites in continuous presence are displayed depending on
the

Viewing mode

setting. If

Viewing mode

is set to

Auto

(continuous presence) or other modes, all participating sites view
continuous presence. If

Full screen

is selected for

Viewing

mode

, the following occurs:

–

If the built-in MCU of the local terminal is being used and if
the local site participates in the conference, the local site is
viewed by the other sites in the conference.

–

If the local site does not participate in the conference, the
participating sites view the site that is specified in the relevant
policy on the terminal whose built-in MCU is being used.

NOTE

Only the built-in MCU of the HUAWEI VP9039A supports the

Free view

mode.

Audio protocol

This specifies the audio protocol used by the terminal to encode and
decode the audio.

Enable dual audio
channel

By selecting

AAC_LD

or

HWA-LD

, you can enable the dual-audio

channel.

Video protocol

This specifies the video protocol used by the terminal to encode and
decode the video. In a non-multi-stream conference, the video protocol
is the video protocol used by the local terminal.
Using the H.263 and H.264 video protocols in an HD conference is
recommended.

Video resolution

You can select a proper format based on the video protocol that is
already set.
When the video protocol is set to

auto

, the video format can be

Sharp

or

Smooth

.

When

Sharp

is selected, the system prioritizes the frame rate. When

Smooth

is selected, the system prioritizes the video resolution.

Video frame rate

This specifies the frame rate used during in video encoding. It is
recommended that you set this parameter to

Auto

. A higher frame rate

equates to smoother video quality and a lower frame rate equates to
clearer video quality.

Enable H.239

After this check box is selected, presentations can be shared during
point-to-point calls.

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

87

«
...
97
98
99
100
101
...
»

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments