Home
/
Huawei
/
9000 VCT V100R011
/
Administrator'S Manual

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 104 / 204

Share

Page: 104 / 204

Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 104

l

After a conference is initiated, the remote sites view the video of the local site before the
presentation.

l

During the layout switch in continuous presence mode, the remote sites can always view
the video of the local site.

To select a video source, perform the following operations:

Press

. Follow the relevant instructions to select a desired video source from multiple video

output interfaces.

To select a presentation source, perform the following operations:

After a conference starts, select

Presentation source

from the option bar. From the

Presentation

source

screen, select a video input interface as the local presentation source.

NOTE

For details about how to operate on the option bar, see section

6.1 Customizing the Option Bar

During an H.239 dual-stream conference, you can change the video and presentation sources.

Choosing Output Destinations

During an H.239 dual-stream conference, if local video and presentation and remote video and
presentation exist simultaneously and if multiple monitors are used at the local site, you can set
the output interfaces for the videos and presentations as required.

For details, see section

3.6 Setting Video Output Parameters

5.5.3 Enabling the H.239 Mode

After enabling the H.239 mode, the video and the presentation can be sent simultaneously during
a conference.

For details about how to enable the H.239 mode, see section

5.3 Setting Conference

. By default, the H.239 mode is enabled on the terminal.

The H.239 mode supports

Presentation

and

Live

.

l

Presentation

: When the video is switched, the presentation remains unchanged. This mode

is used when the presentation carries images, such as slides.

l

Live

: The presentation viewed by each site is switched along with the video. This mode is

used when the presentation carries videos.

During a conference in

Presentation

mode, only one site can share a presentation at a time.

During a conference in

Live

mode, multiple sites can share presentations simultaneously.

5.5.4 Sharing a Presentation

A computer can be connected to the terminal to share files stored in the computer. When you
are sharing files on the computer, the remote sites can view your video and the desktop contents
of the computer.

Prerequisites

The video source of the presentation has been configured, and the presentation parameters have
been set.

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

92

«
...
102
103
104
105
106
...
»

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments