Home
/
Huawei
/
9000 VCT V100R011
/
Administrator'S Manual

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 115 / 204

Share

Page: 115 / 204

Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 115

6

Conference Control

About This Chapter

During a multipoint conference, you can control the video and audio of the participating sites
using conference control functions.

A conference can have only one chair site at a time. Another site can become the new chair site
only after the current chair site releases its chair control rights.

If a conference is held with a built-in MCU, the conference control functions listed in

are available to the terminal whose built-in MCU is being used.

Table 6-1

Terminals and corresponding conference control functions

Terminal

Conference Control
Functions Available to the
Terminal Whose Built-In
MCU Is Being Used

Conference Control
Functions Available to the
Other Participating
Terminals

ViewPoint 9039 with
a built-in MCU
ViewPoint 9036 with
a built-in MCU

Functions to call sites,
disconnect sites, broadcast sites,
stop broadcasting sites, enable or
disable chair control, end a
conference, set continuous
presence, use default continuous
presence, broadcast continuous
presence, enable or disable voice
activation, and lock or unlock a
conference

Function to request chair control
rights

HUAWEI VP9039A
with a built-in MCU
ViewPoint 9039S
with a built-in MCU
HUAWEI VP9036S
with a built-in MCU

Besides the preceding
conference control functions, the
functions to view sites and view
continuous presence are also
available.

Functions to request chair
control rights, set continuous
presence, view sites, and view
continuous presence.

HUAWEI 9000 HD Video Terminal
Administrator Guide

6 Conference Control

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

103

«
...
113
114
115
116
117
...
»

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments