Home
/
Huawei
/
9000 VCT V100R011
/
Administrator'S Manual

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 102 / 204

Share

Page: 102 / 204

Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 102

The HD capabilities of the HUAWEI 9000 are listed as follows:

l

Sending HD video to remote sites

l

Receiving HD video from remote sites

l

Displaying HD video of the local site

The terminal can send or receive the desktop contents of a computer while sending or receiving
HD video. If two channels of streams, which are the video and presentation, can be transmitted
in a conference, the conference is a dual-stream conference. For details, see

5.5 Experiencing

an H.239 Dual-Stream Conference

.

5.4.1 Sending HD Video

To send HD video, perform the following operations:

Procedure

Step 1

Connect the terminal to an HD video source, for example, an HD camera.

Step 2

Choose

Settings

>

Video

>

Video Input

, and then set the HD camera model and other relevant

parameters.

Step 3

Set the conference parameters described in section

5.3 Setting Conference Parameters

as

follows:

l

Set

Video protocol

to

H.264

.

l

Set

Video resolution

to

720p

or a higher resolution.

Step 4

Initiate a conference. The recommended setting of the conference rate is 2 Mbit/s or higher.

----End

5.4.2 Displaying HD Video

To receive HD video from a remote site, perform the following operations:

Context

It is recommended that you use an HD monitor with a 16:9 liquid crystal display (LCD) to display
the HD video. The system can automatically detect the monitor which is connected to the
terminal.

Whether the video is displayed with an aspect ratio of 4:3 or 16:9 depends on the video protocol
and the setting of the video resolution. If the local site needs to display the 4:3 video from a
remote site on the monitor with a 16:9 LCD, the terminal adjusts the video without distorting it.
Black borders may exist at the four sides after the terminal adjusts the video so as not to affect
the viewing experience.

Procedure

Step 1

Connect the terminal to an HD monitor (the recommended interface being HD OUT 1).

Step 2

Choose

Settings

>

Video

>

Video Output

, and then set the video resolution for the HD OUT

interface and configure the interface to output remote video.

HUAWEI 9000 HD Video Terminal
Administrator Guide

5 Initiating a Conference

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

90

«
...
100
101
102
103
104
...
»

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments