manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 68 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 68

Parameter

Description

Display H.239
automatically

This specifies whether the presentation is output from the HD OUT
1 interface automatically.
Only the main output interface supports this function.

Automatic layout
mode

This specifies the display mode of the presentation.

l

Full screen

: The presentation or the video is displayed in full-

screen mode.

l

PiP

: The presentation and the video are displayed in picture-

in-picture mode.

l

PoP

: The presentation and the video are displayed in picture-

out-picture mode.

Only the main output interface supports this function.

Small window position

This specifies the position of the small window displayed on the
main screen. The small window can be displayed in the lower right
corner, lower left corner, upper right corner, or upper left corner.
By default, the small window is displayed in the lower right corner.
Only the HD OUT 1 interface supports this function.
To switch the layout to the picture-in-picture mode, choose either
of the following methods:

l

From the option bar, select 

Layout

 and then 

.

l

Press 

 on the remote control consecutively until the layout

is switched to the picture-in-picture mode.

 

In the following table, ① indicates the local video; ① indicates the local presentation; ① indicates
the remote video; ① indicates the remote presentation.

Table 3-12

 Displayable contents of each video output interface (on the ViewPoint 9039,

ViewPoint 9036, View 9035, and ViewPoint 9033)

Video
Output
Interface

Video
Displayed

Combined
Picture

Default Video
Before
Conference

Default Video
In Conference

HD OUT 1

①②③④

Yes

①

③

HD OUT 2

①②③④

No

②

④

HD OUT 3

①②

No

①

①

 

HUAWEI 9000 HD Video Terminal
Administrator Guide

3 Camera and Display

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

56

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments