Hitachi UX Twin-Nozzle Technical Manual Download Page 59 | Manualshive

Page: 59 / 161

background image

5-6

●

Transmission Sequences

5.3 Transmission Sequences

5.3.1 Common Transmission Sequences

(1) Basic transmission operation.

When ENQ and ACK are present:

External device

IJ printer

ENQ

ACK

STX

Text

ETX

ACK

External device

IJ printer

ACK

ACK

ACK

DC2

ENQ

STX

Text

ETX

External device

IJ printer

STX

Text

ETX

ACK

External device

IJ printer

ENQ

NAK

External device

IJ printer

ENQ

ACK

STX

Text

ETX

NAK

External device

IJ printer

ENQ

ACK

STX

Text

ETX

BCC

ACK

(2) When DC2 (retransmission) code is used

(When no response is received though ENQ has been issued and yet the contents of print
area switched)

When ENQ is omitted:

(3) When the IJ printer is incapable of receiving data or is off-line

(4) Abnormal transmission operation (when the text contains an erroneous message)

(5) When BCC code is included

(6) When the IJ printer power is OFF

No response will be returned for any code transmission from the external decice.

(7) The printings, print specifications, print format, and user pattern data can be

consecutively transmitted in the following order in a single session.

Print format
Print specifications
Printings

2

1

3

(Example)

Print format

Print format

Print format

Print

specification

Print

specification

Print content

The user pattern can be positioned anywhere within the above data chain.
''Line count / print format uniformity'', ''Format setup change'', ''Free layout transmission'',
''Print item deletion transmission'' and ''Count reset transmission'' must be transmitted
independently. If an attempt is made to send it together with the other data, a communication
error (NAK response) occurs.
The print data recall must also be transmitted independently. Even if it is sent together with the
other data, no error occurs. However, the print data recall takes precedence, rendering the other
data invalid.

(8) Up to 3000 bytes of data can be transmitted at a time, including "STX" and "ETX".
If the 3000-byte limit is exceeded, a communication error (NAK response) occurs.

2

1

«
...
57
58
59
60
61
...
»

Summary of Contents for UX Twin-Nozzle


































































































































































Reviews:

No comments

Related manuals for UX Twin-Nozzle

Brand: Xerox Pages: 40

Brand: EasyThreed Pages: 15

Brand: TallyGenicom Pages: 310

Brand: TallyGenicom Pages: 330

KX-MC6040 - Color Laser Multi-Function...

Brand: Panasonic Pages: 24

Brand: Canon Pages: 521

Brand: Canon Pages: 456

Brand: Canon Pages: 542

Brand: DNP Pages: 66

Brand: Inno3D Pages: 23

Brand: Novexx Solutions Pages: 6

VersaUV LEJ-640

Brand: Roland Pages: 321

Brand: Ricoh Pages: 288

Brand: Black Box Pages: 30

Nuvera 100 roduction Systems

Brand: Xerox Pages: 70

LaserMatrix LM2405

Brand: Output Technology Pages: 249

Brand: Ultimaker Pages: 34

Brand: Magicard Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands