GVS CHTC-86/01.1.21 User Manual Download

Page: 17 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

10:30:00, 11:30:00

; "1h" means sending the time to the bus per on hour point, such as

9:00:00, 10:00:00,

11:00:00

Parameters "Warning tone"

Options: disable

enable

The parameters mainly are set in the Thermostat keys about whether to open the tone. "Disable" is

not enabled tone, "enable" to enable beep.

Parameter "Control device"

Options: HVAC

air condition

This parameter is used to select the type of heating and cooling systems. "HVAC" means the fan

coil system, controlling the temperature by controlling fan coil actuator; "air condition" means home air

conditioning system, adjusting household air temperature by controlling the infrared device.

Parameter "Temperature control system"

Options: Cooling

Heating

Heating and Cooling

Basic and additional cooling

Basic and additional heating

Basic and additional Heating and Cooling

This parameter is used to set the temperature control feature, you can select the basic heating and

cooling can also choose the basic heating and cooling plus auxiliary heating and cooling. Select "cooling

/ heating", enabling cooling / heating function, or both enabled, when selecting its options, the

corresponding settings interface "heating / cooling setpoint" and "heating / cooling control" visible in the

interface can be set with the corresponding parameters.

Parameter "Control action when display off"

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands