GVS CHTC-86/01.1.21 User Manual Download Page 60

Page: 60 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

This parameter sets the data type thermostat panel sent to the bus when the set timing time reaches.

Options "Output value"

Options: 0..1/0..3/0..15/0..255/-32768…32767/0..65535/0..4294967295

This parameter sets the data value that is sent to the bus.

4.12 Parameter window "Pushbutton Interface"

Pushbutton Interface has three binary inputs and a temperature sensor input; three binary inputs

can be set to switch, dimming, curtains and other functions. Temperature sensor inputs can be

connected an external NTC thermistor, as an external temperature sensor of thermostat panel, or as a

temperature limiter of underfloor heating, to stop heating when the heating temperature is higher than

the limit.

Figure 4.12.1 Parameter window "Push button Interface"

Parameter "Debounce Time"

Options: 10ms/20ms/„„/150ms

Debounce time set here, to prevent unnecessary repeatedly operations caused by multiple

triggering when the contact repeatedly jitter, which is the minimum effective time of contact input.

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands