GVS CHTC-86/01.1.21 User Manual Download Page 85

Page: 85 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Disable room

temperature timer

Timer

1bit

C,W

1.001 DPT_Switch

This communication object is used to disable or enable the Timer function.

Receive telegram "1" - disable the timer function

Receive telegram "0" - enable the timer function

92/../107

1bit value/../4byte

value

Time X value

(X=1..16)

1bit/../4byte

C, T

1.001 DPT_Switch

2.002 DPT_Bool_Control

3.007 DPT_Control_Dimming

5.010 DPT_Value_1_UCount

8.001 DPT_Value_2_Count

7.001 DPT_Value_2_UCount

12.001 DPT_Value_4_UCount

When the timer time reaches, this communication object sends the appropriate data values to the bus, the

user can select the appropriate data type and value in the parameter "Reaction at regular time" and the parameter

"Output value" as required for transmission.

5.6 "Pushbutton Interface" Communication Object

5.6.1

"Switch" Communication Object

5.6.1 "Switch" Communication Object

Number

Object name

Functions

Data Types

Flags

DPT

53/56/59

Switch 1, input 1/2/3

CH A Switch

1bit

C, W,T

1.001 DPT_Switch

When CH A "Switch" is enabled, this communication object is visible, through short push, according to the parameters

settings, performs the corresponding actions, e.g. ON, OFF, TOGGLE, etc. When the telegram is "1"--- ON; When the

telegram is "0"--- OFF.

54/57/60

Switch 2, input 1/2/3

CH A Switch-long

1bit

C, T

1.001 DPT_Switch

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands