GVS CHTC-86/01.1.21 User Manual Download Page 62

Page: 62 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Figure 4.12.2 parameter window "switch"

Parameter "Reaction on closing the contact

（

rising edge

）

switch 1/2"

Parameter "Reaction on opening the contact (falling edge) switch 1/2"

Options: No function

off

toggle

Here is to set the switch value that the object "Switch, X” sent when performing the operation.

If selecting "no action", no actions will be performed. If selecting "toggle", it will perform the inverse

operation, namely, inverse the last value and send again, such as before executing the "On" to operate,

inverted, perform the "Off" operation.

Parameter "Send object value after voltage recovery (if yes not equal toggle)"

Options: yes

Here to set whether to send the current switch value of “Switch, X" to the bus when power is

restored, this parameter is visible when it does not distinguish between long and short operation.

If selecting "yes", it will send

the current switch value of "Switch, X" to the bus when power is

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands