GVS CHTC-86/01.1.21 User Manual Download Page 14

Page: 14 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

Figure 4.2“General settings “Parameter Settings interface

Parameter “Send ‘In operation’ object”

Options

：

Send value “0” cyclically

Send value “1” cyclically

These parameter set the Thermostat cycle and send a message "1" or "0" to the bus,which shows

that the panel is working well. If fail, it will stop sending the message "1" or "0".Options for "No", do not

send; Options for the value '0' cyclically "send" or "send the value '1' cyclically", Thermostat will send a

message "0" or "1"according to the set period of time, so the object "in operation" and "Transmission

period of" in operation "object" parameter will be visible.

Parameter “Transmission period of "In operation" object”

Options

：

10s

…

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands