GVS CHTC-86/01.1.21 User Manual Download Page 78

Page: 78 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

The communication object is for heating/cooling switchover. Receiving telegram "1"will activate heating; receiving

telegram "0" will activate cooling.

Receiving telegram "1"----- heating

Receiving telegram "0" ----- cooling

Basic comfort temperature (at

heating)

Setpoint

temperature

2byte

C, R, W

9.001 DPT_Value_Temp

This object is mainly used to change the setpoint value of temperature in comfort mode, and after the change, a new

value will be saved when the bus is powered off.

Telegram:

0…50

℃

If the first page parameter "Temperature control system" selects "heating and cooling", this object is mainly used to

change the comfort temperature value of heating; the comfort temperature value of cooling, is determined by the comfort

temperature value of dead zone and heating. More information is seen in 4.4 "switchover between heating and cooling".

Heating setpoint

Setpoint

temperature

2 byte

C, R, W,T

9.001 DPT_Value_Temp

The communication object is used to send the heating setpoint of the current operating mode on the bus, sending way

depends on the parameter “send setpoint" in 4.4. The communication object is used to modify the heating setpoint of the

current operating mode. Note that due to the relative adjustment of setpoint temperature, the setpoint temperature in

standby mode, night mode and frost / heat protection mode can only be increased to the maximum setpoint temperature

comfort mode.

Cooling setpoint

Setpoint

temperature

2 byte

C, R, W,T

9.001 DPT_Value_Temp

The communication object is used to send the cooling setpoint of the current operating mode on the bus, sending way

depends on the parameter “send setpoint" in 4.4. The communication object is used to modify the cooling setpoint of the

current operating mode. Note that due to the relative adjustment of setpoint temperature, the setpoint temperature in

standby mode, night mode and frost / heat protection mode can only be decreased to the minimum setpoint temperature

comfort mode.

Output HVAC status

Temperature

control

1 byte

C, R, T

DPT_HVACStatus

This communication object is used to report the status of temperature control, updated every 30 seconds, the interval

of cyclically sending depends on parameter “Period of sending HVAC status". Each 1byte means as follows:

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands