GVS CHTC-86/01.1.21 User Manual Download Page 21

Page: 21 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

setting the monitoring time to 0, will not be monitoring the external temperature sensor .

Once setting the "external sensor", if the thermostat panel does not receive the temperature send

from external temperature sensor within the set monitoring time, Thermostat will consider the external

sensor is faulty, will stop controlling and control sending packets of controlling stop.

Once setting the "internal and external sensor", if the thermostat panel does not receive the

temperature send by external temperature sensor within the set monitoring time, Thermostat will

consider the external sensor is faulty , so that only use the measurement by Thermostat to control .

The monitoring time will be re-timed, when the thermostat panel receives each packet send from the

external temperature sensor,

Note: The monitoring time from Thermostat for external temperature sensor should be at

least 2 times for the time that the external temperature sensor sending messages for preventing

packets missing.

Parameters "Period of sending temperature"

Options: Do not send

10s

This parameter sets the time interval of sensor for sending temperature to the bus loop through

"Actual temperature".

Parameters "Indoor and outdoor temperature"

Options: disable

enable

The parameter is visible when the "Temperature sensor"

selecting "internal sensor and external

sensor", which can be used to set whether to alternately display the indoor temperature and outdoor

temperature on the display. Outdoor temperature taken from the object 84.

Parameters "Indoor and outdoor temperature switch time (second)"

Options: 0 ... 255 s

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands