GVS CHTC-86/01.1.21 User Manual Download Page 87

Page: 87 / 89

GVS K-BUS

○

KNX/EIB

Thermostat

www.video-star.com.cn

[email protected]

Tel.

：

（

8620

）

39338986

Fax.

：（

8620

）

39338465

53/56/59

Output shutter UP/DOWN

CH A/B/C Blind

1bit/1byte

C, T

1.008 DPT_UpDown

5.001 DPT_Scaling

The communication object, by

sending

commands to the bus, moves up / down curtains.

The communication object can send 1bit or 1bytecommands, by "Function of switchover blinds / roller shutter" choose

curtain type, by "Object type" select the

type. When the communication object is"1bit", send "1" to move

downward; send "0" to move upward. When the telegram is "1 byte", telegrams are sent based on the value set by the

user.

54/57/60

Stop/lamella adj

CH A/B/C Blind

1bit

1byte

C,T

1.007 DPT_Step

5.001 DPT_Scaling

The communication objects, by sending commands to the bus, stop/adjust curtains.

The communication object can send 1bit or 1bytecommands, by "Function of switchover blinds / roller shutter" choose

curtain type, by "Object type" select the telegram type. When the communication object is"1bit", send "1" to stop or move

downward; send "0" to stop or move upward. When the telegram is "1 byte", telegrams are sent based on the value set by

the user.

55/58/61

Disable input 1/2/3

CH A/B/C Disable

1bit

C,W

1.001 DPT_Switch

As above.

5.6.4

"Scene" Communication object

Figure 5.6.4 “scene” communication object

Number

Object name

Functions

Data types

Flags

DPT

53/56/59

Input 1/2/3

，

Scene

Scene number

1byte

C, T

18.001 DPT_SceneControl

Summary of Contents for CHTC-86/01.1.21


























































































Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands

GVS CHTC-86/01.1.21, User Manual

Search results

Summary of Contents for CHTC-86/01.1.21

Reviews:

Related manuals for CHTC-86/01.1.21

Brands by name

Popular brands